Stanton DJ Equipment SMX 301 User Manual

WARRANTY  
This unit has been designed and manufactured using quality  
components. Therefore, it is warranted to be free from defects in  
materials (limited as specified below), and workmanship for a period of  
twelve (12) months from the original purchase date. During this period,  
all service and parts necessary to repair a defect will be free of charge.  
This limited warranty applies to mechanical parts which are subject to  
wear and tear as specified:  
SMX-301  
P R O F E S S I O N A L DJ MIXER  
OWNER’S MANUAL  
• Faders (except P&G fader), specified durability: 15,000 cycles;  
• Rotary potentiometers, specified durability: 10,000 cycles;  
• Switches, specified durability: 10,000 cycles.  
Consequently, the parts listed above are warranted to be free from  
defects in materials and workmanship for a period of thirty days (30)  
days from the original purchase date.  
For the warranty to be valid, please complete the warranty registration  
Mail completed warranty cards to:  
Stanton Magnetics, Inc, 3000 SW 42nd • Hollywood, FL 33312  
REPLACEMENT PARTS  
The following user replaceable parts are available from your local  
Stanton dealer.  
LF301  
CF301  
Line fader  
Crossfader  
PS-16US  
PS-16EU  
PS-16UK  
US Power Supply (110v)  
European Power Supply (220v)  
UK only Power Supply (240v)  
STANTON MAGNETICS, INC  
[email protected] • (954) 689-8833  
w w w . s t a n t o n d j . c o m  
© 2003, Stanton Magnetics, Inc.  
 
DESCRIPTION OF FUNCTIONS  
FADER CLEANING AND INSTALL  
After constant use the SMX-301 faders may need to be cleaned and  
lubricated from time to time. This will ensure long life and keep a  
smooth feeling throughout the fader's lifetime. Follow the instructions  
below to lubricate and clean your faders:  
Removing a fader:  
1. Make sure mixer is powered off and power supply is disconnected from  
back of mixer.  
2. Remove the fader to be cleaned or replaced by unscrewing the 2 outer  
screws on the fader plate (removing the 2 inner screws will detach the  
fader from the fader plate).  
Power: This is the power switch to turn the mixer "ON" or "OFF"  
3. Disconnect the fader from mixer by removing the connector on the  
AC IN: This is the Input connection for the included power supply.  
bottom of the fader.  
Line: Line inputs (represented by the letter L, followed by the input  
number) are used to connect to line level sources such as CD players,  
Mini Discs, DATs, samplers, etc.  
Installing a fader:  
1. Once original fader has been removed, simply plug the 4-pin  
connector into the new fader.  
TT: TT (or phono) inputs are used to connect to turntables.  
2. Place fader back in mixer and replace 2 outer screws to secure fader.  
Ground: Connects to the turntable ground cable to eliminate electrical  
hum. Ground cables are usually supplied with turntables  
Master: Connects to an amplifier, EQ, crossover, or other outboard  
signal processing.  
Booth: This is a second output, like the master output. It is usually used  
as a separate output in the DJ Booth for the DJ to monitor the mix  
REC: This is the record output. The output level is static in this case,  
there are no volume controls. It is used to connect directly to tape or CD  
recorders. The volume can be set from the recording device.  
 
DESCRIPTION OF FUNCTIONS  
DESCRIPTION OF FUNCTIONS  
1. Microphone 1 input - This combo (1/4”/XLR) connector is used to  
connect a microphone. The volume is controlled by the MIC 1 knob.  
2. Mic 1 level - Controls the input level of Microphone input 1.  
3. Mic equalizer - Individual controls for high frequency, midrange, and  
low frequency equalization. The EQ controls both Microphone inputs.  
Note: Any changes made to EQ settings will change the overall  
15  
16  
output level.  
4. Pre fader listen - Selects the channel(s) - 1, 2, or 3 - to be  
previewed in the headphones.  
14  
1
5. Channel faders - Controls the output volume of each channel. The  
signal is routed to the line faders after the gain, EQ, pan, and effects.  
6. Crossfader - The crossfader is used to cross fade between channels  
2
3
17  
17  
17  
1 and 3.  
7. Kill switches - Kill switches are used to completely eliminate Hi,  
13  
12  
Mid, or Low frequencies from the audio. This is used for tricks  
during a mix.  
8. Headphone outputs - This is the headphone output jack to connect  
your headphones.  
9. Cue pan - Fades the headphone output between the PFL signal  
(selected by the Cue Select buttons) and master output, effectively  
allowing the user to preview a mix.  
11  
10  
4
5
10. Cue level - Controls the volume of the headphone output.  
11. Booth level - Controls the booth output level. This is basically a 2nd  
output. It is usually used for monitoring in a DJ booth, but can be  
used for various applications.  
9
7
12. Master output Pan- This is the pan or balance control for the mast  
output.  
13. Master output level - Controls the overall output level of the mixer.  
7
14. Output meters - These LEDs let you know if the audio coming out  
of the mixer is loud enough (or too loud!). If the LEDs reach the red,  
the mixer is probably clipping, or distorting.  
15. Input selectors - These toggle switches select the input source  
between phono and line for each channel.  
6
8
16. Input gains - Controls the input sensitivity level of each channel. An  
LED meter is provided on each of the 3 channels for proper  
adjustment of the levels.  
17. Channel equalizer - Individual controls for high frequency,  
midrange, and low frequency equalization with +9dB/Kill  
adjustments. Note: Any changes made to EQ settings will change  
the overall output level.  
 

Sharp Car Video System N 80TC3 User Manual
Socket Mobile Computer Monitor GFK0121E User Manual
Sony Blu ray Player BOP S2100 User Manual
Sony Camcorder CCD TR23 User Manual
Sony Portable Media Storage SDX1 35C User Manual
Sony Portable Speaker Walkman CD User Manual
Sprint Nextel Cell Phone Katana 2 User Manual
Stiga Lawn Mower TURBO 48 SE COMBI User Manual
Stow Marine Sanitation System SDP 2 User Manual
SVAT Electronics Digital Camera WSE100 User Manual